Terahertz (THz) cell-free massive multiple-input-multiple-output (mMIMO) networks have been envisioned as a prospective technology for achieving higher system capacity, improved performance, and ultra-high reliability in 6G networks. However, due to severe attenuation and limited scattering in THz transmission, as well as high power consumption for increased number of access points (APs), further improvement of network capacity becomes challenging. Reconfigurable intelligent surface (RIS) has been introduced as a low-cost solution to reduce AP deployment and assist in data transmission. However, due to the ultra-wide bandwidth and frequency-dependent characteristics of RISs, beam split effect has become an unavoidable obstacle. To compensate the severe performance degradation caused by beam split effect, we introduce additional time delay (TD) layers at both access points (APs) and RISs. Accordingly, we propose a joint precoding framework at APs and RISs to fully unleash the potential of the considered network. Specifically, we first formulate the joint precoding as a non-convex optimization problem. Then, given the location of unchanged RISs, we adjust the time delays (TDs) of APs to align the generated beams towards RISs. After that, with knowledge of the optimal TDs of APs, we decouple the optimization problem into three subproblems of optimizing the baseband beamformers, RISs and TDs of RISs, respectively. Exploiting multidimensional complex quadratic transform, we transform the subproblems into convex forms and solve them under alternate optimizing framework. Numerical results verify that the proposed method can effectively mitigate beam split effect and significantly improve the achievable rate compared with conventional cell-free mMIMO networks.
To support extremely high data rates, reconfigurable intelligent surface (RIS)-assisted terahertz (THz) communication is considered to be a promising technology for future sixth-generation networks. However, due to the typical employment of hybrid beamforming architecture in THz systems, as well as the passive nature of RIS which lacks the capability to process pilot signals, obtaining channel state information (CSI) is facing significant challenges. To accurately estimate the cascaded channel, we propose a novel low-complexity channel estimation scheme, which includes three steps. Specifically, we first estimate full CSI within a small subset of subcarriers (SCs). Then, we acquire angular information at base station and RIS based on the full CSI. Finally, we derive spatial directions and recover full-CSI for the remaining SCs. Theoretical analysis and simulation results demonstrate that the proposed scheme can achieve superior performance in terms of normalized mean-square-error and exhibit a lower computational complexity compared with the existing algorithms.
Recently, deep learning enabled semantic communications have been developed to understand transmission content from semantic level, which realize effective and accurate information transfer. Aiming to the vision of sixth generation (6G) networks, wireless devices are expected to have native perception and intelligent capabilities, which associate wireless channel with surrounding environments from physical propagation dimension to semantic information dimension. Inspired by these, we aim to provide a new paradigm on wireless channel from semantic level. A channel semantic model and its characterization framework are proposed in this paper. Specifically, a channel semantic model composes of status semantics, behavior semantics and event semantics. Based on actual channel measurement at 28 GHz, as well as multi-mode data, example results of channel semantic characterization are provided and analyzed, which exhibits reasonable and interpretable semantic information.
The emerging 6G network envisions integrated sensing and communication (ISAC) as a promising solution to meet growing demand for native perception ability. To optimize and evaluate ISAC systems and techniques, it is crucial to have an accurate and realistic wireless channel model. However, some important features of ISAC channels have not been well characterized, for example, most existing ISAC channel models consider communication channels and sensing channels independently, whereas ignoring correlation under the consistent environment. Moreover, sensing channels have not been well modeled in the existing standard-level channel models. Therefore, in order to better model ISAC channel, a cluster-based statistical channel model is proposed in this paper, which is based on measurements conducted at 28 GHz. In the proposed model, a new framework based on 3GPP standard is proposed, which includes communication clusters and sensing clusters. Clustering and tracking algorithms are used to extract and analyze ISAC channel characteristics. Furthermore, some special sensing cluster structures such as shared sensing cluster, newborn sensing cluster, etc., are defined to model correlation and difference between communication and sensing channels. Finally, accuracy of the proposed model is validated based on measurements and simulations.
Integrated sensing and communication (ISAC) is a promising technology for 6G, with the goal of providing end-to-end information processing and inherent perception capabilities for future communication systems. Within ISAC emerging application scenarios, vehicular ISAC technologies have the potential to enhance traffic efficiency and safety through integration of communication and synchronized perception abilities. To establish a foundational theoretical support for vehicular ISAC system design and standardization, it is necessary to conduct channel measurements, and modeling to obtain a deep understanding of the radio propagation. In this paper, a dynamic statistical channel model is proposed for vehicular ISAC scenarios, incorporating Sensing Multipath Components (S-MPCs) and Clutter Multipath Components (C-MPCs), which are identified by the proposed tracking algorithm. Based on actual vehicular ISAC channel measurements at 28 GHz, time-varying sensing characteristics in front, left, and right directions are investigated. To model the dynamic evolution process of channel, number of new S-MPCs, lifetimes, initial power and delay positions, dynamic variations within their lifetimes, clustering, power decay, and fading of C-MPCs are statistically characterized. Finally, the paper provides implementation of dynamic vehicular ISAC model and validates it by comparing key simulation statistics between measurements and simulations.
Integrated sensing and communications (ISAC) is a potential technology of 6G, aiming to enable end-to-end information processing ability and native perception capability for future communication systems. As an important part of the ISAC application scenarios, ISAC aided vehicle-to-everything (V2X) can improve the traffic efficiency and safety through intercommunication and synchronous perception. It is necessary to carry out measurement, characterization, and modeling for vehicular ISAC channels as the basic theoretical support for system design. In this paper, dynamic vehicular ISAC channel measurements at 28 GHz are carried out and provide data for the characterization of non-stationarity characteristics. Based on the actual measurements, this paper analyzes the time-varying PDPs, RMSDS and non-stationarity characteristics of front, lower front, left and right perception directions in a complicated V2X scenarios. The research in this paper can enrich the investigation of vehicular ISAC channels and enable the analysis and design of vehicular ISAC systems.
With the increasing demands from passengers for data-intensive services, millimeter-wave (mmWave) communication is considered as an effective technique to release the transmission pressure on high speed train (HST) networks. However, mmWave signals ncounter severe losses when passing through the carriage, which decreases the quality of services on board. In this paper, we investigate an intelligent refracting surface (IRS)-assisted HST communication system. Herein, an IRS is deployed on the train window to dynamically reconfigure the propagation environment, and a hybrid time division multiple access-nonorthogonal multiple access scheme is leveraged for interference mitigation. We aim to maximize the overall throughput while taking into account the constraints imposed by base station beamforming, IRS discrete phase shifts and transmit power. To obtain a practical solution, we employ an alternating optimization method and propose a two-stage algorithm. In the first stage, the successive convex approximation method and branch and bound algorithm are leveraged for IRS phase shift design. In the second stage, the Lagrangian multiplier method is utilized for power allocation. Simulation results demonstrate the benefits of IRS adoption and power allocation for throughput improvement in mmWave HST networks.
Reconfigurable intelligent surface (RIS) emerges as an efficient and promising technology for the next wireless generation networks and has attracted a lot of attention owing to the capability of extending wireless coverage by reflecting signals toward targeted receivers. In this paper, we consider a RIS-assisted high-speed train (HST) communication system to enhance wireless coverage and improve coverage probability. First, coverage performance of the downlink single-input-single-output system is investigated, and the closed-form expression of coverage probability is derived. Moreover, travel distance maximization problem is formulated to facilitate RIS discrete phase design and RIS placement optimization, which is subject to coverage probability constraint. Simulation results validate that better coverage performance and higher travel distance can be achieved with deployment of RIS. The impacts of some key system parameters including transmission power, signal-to-noise ratio threshold, number of RIS elements, number of RIS quantization bits, horizontal distance between base station and RIS, and speed of HST on system performance are investigated. In addition, it is found that RIS can well improve coverage probability with limited power consumption for HST communications.
The critical distinction between the emerging intelligent transparent surface (ITS) and intelligent reflection surface (IRS) is that the incident signals can penetrate the ITS instead of being reflected, which enables the ITS to combat the severe signal penetration loss for high-speed railway (HSR) wireless communications. This paper thus investigates the channel estimation problem for an ITS-assisted HSR network where the ITS is embedded into the carriage window. We first formulate the channels as functions of physical parameters, and thus transform the channel estimation into a parameter recovery problem. Next, we design the first two pilot blocks within each frame and develop a serial low-complexity channel estimation algorithm. Specifically, the channel estimates are initially obtained, and each estimate is further expressed as the sum of its perfectly known value and the estimation error. By leveraging the relationship between channels for the two pilot blocks, we recover the Doppler shifts from the channel estimates, based on which we can further acquire other channel parameters. Moreover, the Cramer-Rao lower bound (CRLB) for each parameter is derived as a performance benchmark. Finally, we provide numerical results to establish the effectiveness of our proposed estimators.
Reconfigurable intelligent surface (RIS) has received increasing attention due to its capability of extending cell coverage by reflecting signals toward receivers. This paper considers a RIS-assisted high-speed train (HST) communication system to improve the coverage probability. We derive the closed-form expression of coverage probability. Moreover, we analyze impacts of some key system parameters, including transmission power, signal-to-noise ratio threshold, and horizontal distance between base station and RIS. Simulation results verify the efficiency of RIS-assisted HST communications in terms of coverage probability.